How to Apply Rust-Oleum RockSolid Garage Floor Coating

Rust-oleum RockSolid garage floor coating

Transform your garage into a stunning new space with showroom-quality. Rust-Oleum RockSolid® Garage Flooring Coating is 20x stronger than epoxy. Resistant to salt, oil, gas, and other harsh chemicals, this floor coating is perfect for upgrading any garage floors. The “World’s Toughest Coatings” will last a lifetime while looking fantastic! 

No need to hire a professional with for this project. The RockSolid Garage Floor Coating Kit comes in one-car and two-car kit options, a variety of color combinations, and can be installed in one day. Rust-Oleum RockSolid for your garage is a dream product for DIYers. It gives you a professional look, for less money, and in less time!

RockSolid Garage Floor Coating

 

According to Amy Mickschl, brand manager at Rust-Oleum:

For so many homeowners, the garage has become an extension of their living space, it’s become the workshop, home gym or extra space for family parties. A coated floor goes a long way in transforming the space into a new place to gather.


These instructions will show you how to use Rust-Oleum RockSolid Garage Floor Coating.

Here’s what you’ll need to know before you get started:


RockSolid Garage Floor Coating

Each Kit Contains:

 - Pre-Tinted Polycuramine™ Burst Pouch

-  Foam Roller

-  Decorative Color Chips

-  Instructions

-  Stir Stick

-  Concrete Etch

 

Additional Items You May Need:

-  Hard Bristle Broom

-  Shop Vac

-  Paint brush

-  Painter’s Tape

-  Roller Pole

-  2 gal bucket


Car in the Garage

How Much Surface Area Are You Covering?

  •  The 1 Car Kit covers up to 200-500 sq ft

  • The 2 Car Kit covers up to 450-500 sq ft

Note:  Trying to stretch these coverage rates can result in loss of gloss and color tone problems.

 

What’s Polycuramine?

Polycuramine is a blend of Polyurea, Polyurethane, and Epoxy. It combines all the best components of each chemical into one self-leveling, flexible, fast curing, high-gloss, and indestructible coat. RockSolid Polycuramine comes in the Garage Floor Kit with an easy-to-mix pouch that combines A and B components. No mixing bucket required.


Crack Repair

Step 1: Preparation


Preparation is key to any product. If your concrete floor has been previously coated, you'll need to prime it with Rust-Oleum Garage & Concrete Floor Primer it to prepare your concrete to be top coated with RockSolid Garage Coating. Using primer will eliminate the need to rent or buy a sander or grinder.


Etching

If your garage floor hasn’t been previously coated, you will want to clean the area using a broom and vacuum. Garages with heavier stains will need a degreaser. Thoroughly scrub and rinse the surface. Once cleaned, etching the floor is important to allow for proper adhesion. Etching opens the pores of concrete allowing the coating to adhere better. Use the supplied etch rinsing with water thoroughly. Allow to dry completely. Lastly, fill any cracks and tape off any areas around the perimeter you feel necessary.

 

Best Conditions for Application:

-  40-90 Degrees

-  Low Humidity

-  Adequate Ventilation

-  Rain-Free for 48 hours


Pour

Step 2: Mix, Shake, and Pour


Burst the pouch by rolling part A into part B allowing components to mix together. Shake the pouch for 2-3 minutes to ensure the two components are combined. Pour the mixture along the edges and corners in 2-3” wide ribbons. Cut in the edges with a paint brush. Mix only one pouch at a time.

Rollout

Step 3: Roll Out


Pour a small amount of the mixture on the floor. Working in 4’x4’ sections, roll it out using M and W patterns. Pull the mixture thread back and then push it forward to fill any bare spots between sections. Avoid creating thick spot and don’t be afraid to overlap.

Broadcasting look

Step 4: Broadcast


Paint a strip along the back wall, approximately 2-3' out from the wall. Spread your paint chips by throwing them up in the air over most of the 2-3' strip leaving 6-12" without chips. Pour a new ribbon of product 2’ away from previously coated area. Roll the next section and broadcast the paint chips again. Repeat these steps until your entire floor is covered. Average cure time is 8-10  hours for foot traffic and 24 hours for drive on traffic.


Check out how others are using Rust-Oleum Rocksolid to transform their spaces on Rustoleum's Garage Pinterest Page!

Garage Makeover with Rust-oleum RockSolid

Garage Makeover with Rust-Oleum RockSolid


Rust-Oleum RockSolid is easy to apply, easy to maintain, and comes with a lifetime warranty. Rust-Oleum RockSolid also makes Metallic Floor Coatings as well! 


As you can see, preparation is key to applying Rust-Oleum RockSolid garage floor coatings. Beginners and expert DIYers, follow these 4 simple steps to easily transform your garage spaces. Order from doitbest.com, or pick one up at your local Do it Best store!


Rust-Oleum RockSolid Products:

Top of Page